DPR2: DinoKoll Porcelain Slab Fast
One component, thixotropic highly deformable, high performance, rapid- setting and hydration cementitious adhesive, which is easy to apply by trowel with no vertical slip and extremely high yield for porcelain (slab) ceramic tiles and stone material. walk over time of a few time.
- DPR2:
DPR2 is abbreviation of Dinokoll Porcelain Rapid adhesive for Installation corresponds EN12004 in C2FTE(S2) class for Fast instalment.
C2: refer to cement based adhesive improved adhesion.
- F: Fast instalment.
- T: is adhesive with limited vertical slip.
S2: Highly deformable adhesive according to the norm EN12002.
- E: Is adhesive with extended open time.
⚫ Application:
- To apply for fast setting big size of porcelain wall and floor façade, inside and outside, terrace and balconies. - To apply ceramic on traditional ceramic.
To apply all kind of glass and ceramic mosaic on cement and on heating screeds.
-
For quick restructuring work were immediate installation is required (supermarkets, airports, public building etc.)
Suitable for bonding on deformable substrates (marin board) wooden agglomerates which are shfficiently stable in the presence of water, old wooden floor, etc.
- Advantages:
- No sliding in vertical applications.
- Appling tile over tile on heating screed.
- The volume and density of adhesive.
- Self contact (back buttering).
- Fast setting and walk over of a few time.
- Highly recommend to use self levelling before DPR2.
- Help to reducing the noise caused by foot steps.
- Consumption:
- The thickness should not more than 15 mm and 8 kg/ m2 for one side. and the water ratio is about (22%-27%) weight of adhesive.
How to mix
It is better to use electric mixers or mixers that are installed on a drill and use them for 3
to 5 minutes from the time of mixing until you reach a soft, one-hand mortar and free of bubbles mixture. Then the adhesive mortar is rested for 3 to 5 minutes and mixed again for another 30 seconds, now the adhesive is ready to use.
- How to use the adhesive:
The surface of the adhesive application must be completely dry, smooth, and level, and also free from any dust, grease, paraffin oil, or any other substance that causes the substructure and connection to be loose.
The said place should not be exposed to freezing or high temperatures for at least 24 hours. Also, if the working environment has a temperature rise above 35 degrees Celsius, you can moisten the substrate a little, and at a temperature below 5 degrees Celsius, you must warm the environment.
The use of dinokoll primer in the relative strength and insulation of the substructure will reduce the amount of adhesive consumption and increase adhesion.
Initial tensile adhesion strength (after 28 days) |
> 1 N/mm2 |
Tensile adhesion strength after heat ageing |
> 1 N/mm2 |
Tensile adhesion strength after water immersion |
> 1 N/mm2 |
Tensile adhesion strength after freeze-thaw cycle |
> 1 N/mm2 |
Tensile adhesion strength (after 6 hours) |
> 0.5 N/mm2 |
Slip |
< 0.5 mm |
Open time |
30 min |
Transverse deformation |
> 5 mm |
- Cleaning:
After finishing the installation of porcelain and its grouting, the joints should be cleaned immediately with a sponge and water. Other than this, after the grouting material hardens, you must use a specialized cleaner material from Dinokoll to clean the remaining effects of cement and grouting materials.
- Storage:
The place where the adhesive is stored should be cool and dry, and the adhesive should be kept in a closed envelope.
The best consumption time is one year after the production date under the above conditions.
- Responsibility
This company fully accepts the qualitative and quantitative responsibility of all its products in accordance with the relevant standards and will be responsible for any deficiency. But matters of how to maintain, use, operate, and implement it are the responsibility of the respective customers.
- Safety measures:
This product contains Portland cement, which leads to an alkaline reaction when in contact with moisture. Use gloves while using the product; in case of direct contact with the skin, it will cause burning, dryness, and cracking of the skin. It may cause an allergic reaction.
In cases of direct contact with the eyes, it may cause sensitivity, burning in the cornea, or even chemical burns. In the event of contact with the eyes, wash with water for 20 minutes and then consult a doctor.
In addition, detachable elastics must be used every 25 square meters inside, every 10 square meters outside, and every 4 meters in height.