DWF2: DinoKoll Wall and Floor

One-component thixotropic cement-based adhesive with extended open time for indoor and outdoor installation of single and double fired materials on cement-based substrates.


- DWF2 is abbreviation of Dinokoll Tile Adhesive for

Wall and Floor tile corresponds EN12004 in CITE class.

- Cl: standard setting cement-based adhesive.

- T: is adhesive with limited vertical slip.

- E: is adhesive with extended open time.


- Usuall wall and floor ceramic tile, inside and outside.

⚫ Advantages:

- Easy to prepare and apply.

- No sliding in vertical applications.

- Long using period, extend open time.

- The volum of adhesive.

- Thixotropy adhesive.

. Consumption:

- The best pulling adhesive with notched trowel and back of tile with thin spatula. The thickness should not more than 10 mm and consumption of adhesive is about 3-4 kg/m2 for one side and 5 kg/m2 for both side in medium size and 4-5 kg/m2 for one side and 6 kg/m2 in both side for biger size. and the water ratio is about (22% -24%) weight of adhesive.


How to mix

It is better to use electric mixers or mixers that are installed on a drill and use them for 3

to 5 minutes from the time of mixing until you reach a soft, one-hand mortar and free of bubbles mixture. Then the adhesive mortar is rested for 3 to 5 minutes and mixed again for another 30 seconds, now the adhesive is ready to use.

  • How to use the adhesive:

The surface of the adhesive application must be completely dry, smooth, and level, and also free from any dust, grease, paraffin oil, or any other substance that causes the substructure and connection to be loose.

The said place should not be exposed to freezing or high temperatures for at least 24 hours. Also, if the working environment has a temperature rise above 35 degrees Celsius, you can moisten the substrate a little, and at a temperature below 5 degrees Celsius, you must warm the environment.

The use of dinokoll primer in the relative strength and insulation of the substructure will reduce the amount of adhesive consumption and increase adhesion.

Wall and Floor Adhesive - DWF2

Initial tensile adhesion strength (after 28 days)

> 1 N/mm2

Tensile adhesion strength after heat ageing 

> 1 N/mm2

Tensile adhesion strength after water immersion

> 1 N/mm2

Tensile adhesion strength after freeze-thaw cycle

> 1 N/mm2

Tensile adhesion strength (after 6 hours)

> 0.5 N/mm2


< 0.5 mm

Open time

10 min


  • Cleaning:

After finishing the installation of porcelain and its grouting, the joints should be cleaned immediately with a sponge and water. Other than this, after the grouting material hardens, you must use a specialized cleaner material from Dinokoll to clean the remaining effects of cement and grouting materials.

  • Storage:

The place where the adhesive is stored should be cool and dry, and the adhesive should be kept in a closed envelope.

The best consumption time is one year after the production date under the above conditions.

  • Responsibility

This company fully accepts the qualitative and quantitative responsibility of all its products in accordance with the relevant standards and will be responsible for any deficiency. But matters of how to maintain, use, operate, and implement it are the responsibility of the respective customers.

  • Safety measures:

This product contains Portland cement, which leads to an alkaline reaction when in contact with moisture. Use gloves while using the product; in case of direct contact with the skin, it will cause burning, dryness, and cracking of the skin. It may cause an allergic reaction.

In cases of direct contact with the eyes, it may cause sensitivity, burning in the cornea, or even chemical burns. In the event of contact with the eyes, wash with water for 20 minutes and then consult a doctor.

In addition, detachable elastics must be used every 25 square meters inside, every 10 square meters outside, and every 4 meters in height.